BRIDGELESS PFC IMPLEMENTATION USING ONE CYCLE CONTROL TECHNIQUE PDF

In this paper, One Cycle Control technique is implemented in the bridgeless PFC. By using one cycle control both the voltage sensing and current sensing. rectifier and power factor correction circuit to a single circuit, the output of which is double the voltage implementation of One Cycle Control required a better controller. . The figure shows a typical buck converter using PWM technique. PWM switching technique is used here as implementation of One Cycle Power Factor Correction, Bridgeless voltage Doubler, Buck Converter, One Cycle Control This problem can be solved by using bridgeless converters to reduce the.

Author: Brakinos Yomuro
Country: Nigeria
Language: English (Spanish)
Genre: Finance
Published (Last): 26 September 2007
Pages: 157
PDF File Size: 14.55 Mb
ePub File Size: 16.19 Mb
ISBN: 515-5-76961-331-6
Downloads: 28254
Price: Free* [*Free Regsitration Required]
Uploader: Yozshujora

Compared to the average current mode control, one cycle control shows many benefits such as no multiplier requirement, no input voltage sensing requirement, and no inductor current sensing requirement. The prototype of a typical converter is shown below. This method is a non linear control technique to control the duty ratio of the switch bridgelless real time such that in each half cycle the average value of the chopped waveform is made equal to the reference value. Therefore, the output voltage jumps up and the typical output voltage transient overshoot will be observed implementatlon the output voltage.

The results obtained are also presented in this paper.

Bridgeless PFC Implementation Using One CycleControl Technique

The bridgeless buck converter was designed for an output voltage of 12V dc. The output obtained is amplified and is fed to an integrator with reset.

  HUSCO 5000 PDF

This drop of efficiency at low line can cause increased input current that produces higher losses in semiconductors and input EMI filter components. How to Cite this Article? The hardware setup of the circuit is designed and implemented. The PWM control method which was already used for controlling the switching has been studied and analysed in this paper using suitable waveforms.

I would like to thank my internal guide Prof. This paper explains a new control method called One Cycle Control [6] which is a non linear control technique and produce faster response than the later one. Efficiency is further improved by eliminating input bridge diodes in which two diodes carry the input current. The one-cycle controller is comprised of an integrator with reset, a comparator, a flip-flop, a clock and an adder.

As a result the control reference is linearly modulated into the duty ratio signal. The experimental results show both efficiency improvement and good power factor correction function. Since the switches are located between the input and the output capacitors, switches S1 and S2 can actively control the input inrush current during start-up. When the switch is turned on by a fixed frequency clock pulse, voltage available across the diode is being integrated.

The values of inductors and capacitor is designed to obtain an output of 12 V DC. Bridgelesss voltage doubler circuit combines both the rectifier and power factor correction circuit to a single circuit, the output of which is double the voltage produced by a single buck converter [3] used as pfc circuit. Conventional ac-dc converters has a diode bridge rectifier followed by power factor correction circuit. PWM switching technique is used here as implementation of One Cycle Control required a better controller.

  GIN TONIC ET CONCOMBRE PDF

One Cycle Control of Bridgeless Buck Converter

A prototype of voltage doubler buck converter generating a dc voltage of 12V operating at a switching frequency of 65kHz is developed. Since the switched variable always follows the techbique reference the output voltage is independent of all input voltage variations.

I extend my deep sense of gratitude and hearty thanks to Prof. The input voltage and current waveforms, gating signals and the technlque obtained are shown.

The input current flows through only one diode during the conduction of a switch, i.

One Cycle Control of Bridgeless Buck Converter | Open Access Journals

The output of the flip flop is the required gating pulse for the switches. This new control method is very general and directly applicable to all switching converters. As long as the area under the diode-voltage waveform in each cycle is the same as the control prc signal, instantaneous control of the diode-voltage is achieved.

Among these topologies, the bridgeless boost does not require range switch and shows both simplicity and high performance. The operation of an OCC controller is explained by means of the following waveforms.

Switching converters are pulsed and nonlinear dynamic systems. In this paper ,a new control method called One Cycle Control is used for controlling the buck converter during both half of supply omplementation.